Seagate Momentus 5400.2 SATA ST96812AS Manuel d'utilisateur

DETAILED USER’S MANUALv1.0v1.0ELITERAID ER104UT+(B)

10 2.4 R0 MODE The R0 MODE storage policy distributes access across all hard disks. R0 MODE presents the best data speed but no data redundancy. R0

11 Although the volume remains available during the rebuild process, the volume is susceptible to data loss through damage to the remaining drive unt

12 2.7 R3 MODE The R3 MODE storage policy requires a minimum of 3 drives to implement. The R3 MODE adds fault tolerance to drive striping by includi

13 stripes. The data and parity information is arranged on the drive array so that parity is written to all drives. There are at least 3 members to a

14 3 CONFIGURATION 3.1 CONFIGURATION PREREQUISITES 3.1.1 SATA HOST CONNECTIONS This guide assumes that you have already attached the EliteRAID ER

15 3. The following message then appears: “Safe to Remove Hardware”. You can now safely disconnect the device from your computer. Note: If your host

16 4. Turn on the power than release the SETUP BUTTON to complete mode setting. 3.5.3 CLONE MODE The CLONE MODE storage policy requires a minimum o

17 4. Turn on the power than release the SETUP BUTTON to complete mode setting. 3.5.6 R1 MODE The R1 MODE storage policy requires 2 drives to imple

18 3. Press and hold the recessed SETUP BUTTON. 4. Turn on the power than release the SETUP BUTTON to complete mode setting. 3.5.10 R3 MODE WITH H

19 4. Press and hold the recessed SETUP BUTTON. 5. Turn on the power than release the SETUP BUTTON. 6. Turn off the power. 7. Insert the hotspare

2 TABLE OF CONTENTS 1 WELCOME ...

20 4 PARTITIONING VOLUMES 4.1 PARTITION A VOLUME 4.1.1 WINDOWS SYSTEMS Note: Before repartition a volume, back up your data and delete previously

21 checked and click OK. The disk should now be marked as a Basic disk. If a disk appears as “Dynamic”, right-click the disk icon, and select Revert

22 4. Click Next to start the Partition Wizard. 5. Select the Primary or Extended option and click Next.

23 6. Specify the partition size. By default, the partition occupies the entire volume. Click Next. 7. Assign a drive letter or mount path and clic

24 8. Name and format the partition and click Next. 9. Review the file system settings and click Finish to create the logical partition.

25 10. Repeat steps 1 through 9 to partition any remaining disks. 4.1.2 MACINTOSH SYSTEMS Note: Before reconfiguring a volume, back up your data an

26 2. Select a configured disk and click the Partition tab. This procedure illustrates the LARGE Storage Policy configuration, which concatenates the

27 Disk Utility mounts the created partition and represents it with an icon on the desktop. The icon is labeled with the partition name. 9. Repeat

28 5 APPENDIX 5.1 FAQ If you need some help for troubleshooting, please check the frequently asked question below, it may help you problem solved q

29 Maxtor 320GB DiamondMax® 21 STM3320620AS 3.AAE Maxtor 300GB DiamondMax® 10 6L300S0 BANC1G10 Maxtor 250GB DiamondMax® 21 STM3250310AS 3.AAF Maxtor

3 3.6 REBUILDING A REDUNDANCY OR HOT SPARE DRIVE...19 3.6.1 REBUILDING A REDUNDANCY DRIVE

30 Western Digital 160GB WD Caviar® Blue WD1600AAJS-22PSA0 05.06H05 Western Digital 160GB WD Caviar® Blue WD1600JS-22MHB0 02.010C3 Western Digita

4 1 WELCOME 1.1 INTRODUCTION Thank you for choosing EliteRAID ER104UT(-B) storage appliance. It is a hardware RAID solution for digital home and sma

5 1.2 PRECAUTION Please read the safe precautions carefully before you using EliteRAID ER104UT(-B) storage appliance. Ensure that you use the produc

6 z 1 host port (eSATA or USB) to 4 Serial ATA hard disk drives. z Compatible with SATA Gen1 and Gen2 host controllers. z Compatible SuperSpeed US

7 1.5 SYSTEM REQUIREMENTS 1.5.1 PC SYSTEMS • Intel Pentium-III 500MHz equivalent or faster • Windows XP, Windows Vista, Windows 7 RC2 with the la

8 2 STORAGE POLICIES You can configure the EliteRAID ER104UT(-B) storage appliance to use any of the following storage policies to map the appliance

9 It is also possible to create a LARGE volume using only a single hard disk drive connected to Port 1. However, it is not possible to expand an exi