. . . . . . . . . . . . . . . . . . . . . . . . . . . . .HAWK 2LP Family:. . . . . . . . . . . . . . . . . . . . . . . . . . . . .(Wide bus). . . . .
Installation OverviewInstallation of the drive can be divided into distinctphases. Some of these may not be applicable to allsystem installation requi
• Low-Level formatting: All Hawk 2LP wide familydrive models are low-level formatted at the factoryand do not require this step during installation. I
Product repair informationService requirementsThe special facilities required for the manufacture ofthese drives generally prohibit repair in the fiel
• Place drive on a flat, static dissipative surface andhandle with extreme care. Always follow all EOS/ESD precautions to avoid damage to the electric
Warranty: Contact your Seagate Authorized Distribu-tor, Dealer or other purchase source for warrantyinformation.If the drive is no longer under warran
SeaFone telephone number: 408/438-8222The enhanced phone system provides recorded tech-nical information on selected Seagate products whileyou are on
With this service you can access:• Specifications and jumper configurations for allSeagate products.• Reprints of Seagate documentation.• A directory
Hawk 2LP family (Wide) informationCharacteristics of the various drives covered by thismanual are listed in the following table.Legend for table colum
Initial setup informationFor the initial setup connect the cables or plug into amounted connector (if applicable), set the drive ID onthe bus and enab
Hawk 2LP (Wide) Installation Guide, Rev. A 17DC Power connectionHawk 2LP family "W/WD" model drives receive DCpower through a 4 pi
ContentsIntroduction... 1Electromagnetic interference ... 1Be
18 Hawk 2LP (Wide) Installation Guide, Rev. ASCSI address selectionOn "W" and "WD" model drives, make sure that theSCSI
Terminator resistor packsAs a factory installed option, Hawk 2LP family model"W" drives can have terminator resistor packs that arepermanen
20 Hawk 2LP (Wide) Installation Guide, Rev. ARead/Write head auto-parkSeagate disc drives described herein park the headsautomatically at po
Hawk 2LP (Wide) Installation Guide, Rev. A 21Figure 2a. Hawk 2LP family W/WD models I/Oconnection (68 pin SCSI I/O connector)."W"
Drive configurationEach disc drive has option select header connectors onthe back, side and front where jumper plugs are in-stalled to select the way
Hawk 2LP family "WC" and "DC" model 80 pin SCSII/O drivesOn Hawk 2LP family "WC" and "DC" model drives thereis
24 Hawk 2LP (Wide) Installation Guide, Rev. ADrive with HDA up,PCB down, viewedfrom frontPin 1HDAJ6 [1]SCSI ID = 0SCSI ID = 1SCSI ID = 2S
Hawk 2LP (Wide) Installation Guide, Rev. A 25J1-DC PowerJ168 PinSCSI I/OConnectorDriveHDASCSI ID = 8SCSI ID = 9SCSI ID = 10SCSI ID = 11SC
J2Drive FrontPin 1EndJ6Pin 1J2J1DelayMotor StartEnableMotor StartWrite ProtectParity OptionJumperPositionsTEDSMEWPPESSTPTP[8][8]Pin 1HDADr
Notes for Figure 3a, 3b and 3c:[1] Notes explaining the functions of the various jump-ers on jumper header connectors J2, J1-auxiliaryand J6 are given
Hawk 2LP (Wide) Installation Guide, Rev. A 1IntroductionThis manual is organized to assist you in the installationand operation of your Seagate Hawk 2
28 Hawk 2LP (Wide) Installation Guide, Rev. A[4] The drive time-shares the ID and BUSY LED func-tions of J6 and J1-auxiliary. That is, a cab
Hawk 2LP (Wide) Installation Guide, Rev. A 29continued from previous pageDS MEOff Off Spindle starts immediately after power up -Default set
continued from previous pageSSOff On Reserved. Default is no jumper installed.TP TP (Not applicable to "WC/DC" model drives)Off Off No termi
Hawk 2LP (Wide) Installation Guide, Rev. A 31continued from previous pageI/O pin 26 to the drive's internal termina-tors (for single-en
32 Hawk 2LP (Wide) Installation Guide, Rev. Acontinued from previous pagefuture time when the ID is changed theuser could fail to configure
Hawk 2LP (Wide) Installation Guide, Rev. A 33Drive installationThis section describes the physical mounting of thedrive in the host cabinet
34 Hawk 2LP (Wide) Installation Guide, Rev. ABJHK[2]Notes:[1][2][3][4]Inches Millimeters5.74 4.00 1.00 2.362.6204.000.2501.
Hawk 2LP (Wide) Installation Guide, Rev. A 35AFDE[1][3]BGInchesABCDEFGHJKL145.80 101.60 25.40 60.00 15.75 101.60 6.35 44.45 95.25 6
36 Hawk 2LP (Wide) Installation Guide, Rev. ADo not power up the host system until the drive ismounted and the system cover is replaced.• Conn
Hawk 2LP (Wide) Installation Guide, Rev. A 37SCSI interface drivesThe SCSI interface handles both drive geometry anddefect management intern
2 Hawk 2LP (Wide) Installation Guide, Rev. Aand Regulations nor the Radio Interference Regula-tions of the Canadian Department of Communic
Seagate Technology, Inc.920 Disc Drive, Scotts Valley, CA. 95066-4544, USAPublication Number: 77767478, Rev. APrinted in USA
Hawk 2LP (Wide) Installation Guide, Rev. A 3Before you beginVerify that the system is switched off and discon-nected from main power before any inst
4 Hawk 2LP (Wide) Installation Guide, Rev. A• When transporting or shipping a drive or system,please ensure that they are correctly packed
Hawk 2LP (Wide) Installation Guide, Rev. A 5Caution. The circuit assemblies and components con-tained in this equipment can be degraded or
Safety instructions1. The disc drive(s) are to be installed in a customersupplied enclosure where the surrounding air doesnot exceed 50oC.2. Four (4
Sicherheitsanleitung1. Däs Gerät ist ein Einbaugerät, vorgesehen für einemaximale Umgebungstemperatur von 50oC.2. Zur Befestigung des Drives werden 4
Commentaires sur ces manuels