Seagate HAWK 2 ST12400W/WD/WC Guide d'installation

Hawk 2 (Wide bus) Family Install Guide, Rev. C(Wide Bus)ST12400W/WD/WCST11900W/WD/WCHAWK 2 Family:. . . . . . . . . . . . . . . . . . . . . . .. . . .

Hawk 2 (Wide bus) Family Install Guide, Rev. C8Installation OverviewInstallation of the drive can be divided into distinctphases as outlined below. S

Hawk 2 (Wide bus) Family Install Guide, Rev. C• Low-level formatting: After the drive has beenproperly configured for the system, it does not needto b

Hawk 2 (Wide bus) Family Install Guide, Rev. C10Product repair informationService requirementsThe special facilities required for the manufacture oft

Hawk 2 (Wide bus) Family Install Guide, Rev. CShipping: When transporting or shipping a drive, aSeagate approved container must be used. Keep yourorig

Hawk 2 (Wide bus) Family Install Guide, Rev. CIf the drive is no longer under warranty contact pur-chase source for repair information or refer to nu

Hawk 2 (Wide bus) Family Install Guide, Rev. CSeaTDD: 408/438-5382TDD is a Telecommunication Device for the Deafwhere two people can communicate using

Hawk 2 (Wide bus) Family Install Guide, Rev. C14With this service you can access:• Specifications and jumper configurations for allSeagate products.•

Hawk 2 (Wide bus) Family Install Guide, Rev. C 15Drive specificationsProduct Hawk 2 family (wide)Information ST12400W/WC ST12400WDInterface [

Hawk 2 (Wide bus) Family Install Guide, Rev. CProduct Hawk 2 family (wide)Information ST11900W/WC ST11900WDInterface [7] SCSI-2 Fast SCSI-2F

Hawk 2 (Wide bus) Family Install Guide, Rev. C 17Notes.[1] Standard units are factory formatted with 512 databytes per sector. ST12400 OEM standard m

Hawk 2 (Wide bus) Family Install Guide, Rev. CContentsIntroduction... 1Electromagnetic inte

Hawk 2 (Wide bus) Family Install Guide, Rev. C18Initial setup informationFor the initial setup connect the cables, set the SCSIbus address and enable

Hawk 2 (Wide bus) Family Install Guide, Rev. CDC PowerConnectorPin1P2P3P4PPower+12V+12V ret+ 5V ret+ 5VJ11P2P3P4P68 Pin SCSI I/OConnectorJ

Hawk 2 (Wide bus) Family Install Guide, Rev. CIf the drive LED shows no on/off activity when the hostis trying to communicate with it, an incorrect b

Hawk 2 (Wide bus) Family Install Guide, Rev. CModel numbers that end in "WD" have differential I/Ocircuits and these drives and "WC&quo

Hawk 2 (Wide bus) Family Install Guide, Rev. CJ1-AuxiliaryPin 1A68 PinSCSI I/OConnectorJ1-DC PowerPin 1PJ6J2J1 Pin 1J6J2Pin 180 PinSCSI I/Oand

Hawk 2 (Wide bus) Family Install Guide, Rev. CDrive configurationEach disc drive has option select header connectors onthe back, side and front where

Hawk 2 (Wide bus) Family Install Guide, Rev. C24ST12400WC family 80 pin SCSI I/O drivesOn Hawk 2 family, ST12400WC model drives there isno J1-auxilia

Hawk 2 (Wide bus) Family Install Guide, Rev. CFigure 3a. Drive configurator Hawk 2 familyST12400W/WD model (Wide bus) family25SCSI ID = 8SCSI ID = 9SC

Hawk 2 (Wide bus) Family Install Guide, Rev. CFigure 3b. Drive configurator Hawk 2 familyST12400W/WD model (Wide bus) familyJ1-DC PowerJ168 Pin SCSI

Hawk 2 (Wide bus) Family Install Guide, Rev. CFigure 3c. Drive configurator Hawk 2 familyST12400WC model (Wide bus) familySCSI ID = 8SCSI ID = 9SCSI I

Hawk 2 (Wide bus) Family Install Guide, Rev. CIntroductionBefore attempting any installation, please read throughall applicable sections of this docum

Hawk 2 (Wide bus) Family Install Guide, Rev. CNotes for Figure 3a, 3b and 3c:[1] Notes explaining the functions of the various jumperson jumper heade

Hawk 2 (Wide bus) Family Install Guide, Rev. C[4] The drive time-shares the ID and LED/SSP functions ofJ6 and J1-auxiliary. That is, a cable may be at

Hawk 2 (Wide bus) Family Install Guide, Rev. Ccontinued from previous pageOff On Drive spindle does not start until Start Unit com-mand received from

Hawk 2 (Wide bus) Family Install Guide, Rev. Ccontinued from previous pageTP TP (Not applicable to "WC" model drives)Off Off No terminator p

Hawk 2 (Wide bus) Family Install Guide, Rev. CJ6 and J1-AuxiliaryJumperInstallation Jumper Function DescriptionA3,A2,A1,A0* Drive ID on SCSI Bus. The

Hawk 2 (Wide bus) Family Install Guide, Rev. CDrive installationThis section describes the physical mounting of thedrive in the host cabinet and the l

Hawk 2 (Wide bus) Family Install Guide, Rev. CAFDEC[1][3]BGJHK[2]Notes:[1][2][3][4]Inches Millimeters5.74 4.00 1

Hawk 2 (Wide bus) Family Install Guide, Rev. CFigure 5. Hawk 2 family ST12400WC model drivemounting configuration dimension (80 pinI/O connector)AFDEC

Hawk 2 (Wide bus) Family Install Guide, Rev. C36Do not power up the host system until the drive ismounted and the system cover is replaced.• Connect

Hawk 2 (Wide bus) Family Install Guide, Rev. CSCSI interface drivesThe SCSI interface handles both drive geometry anddefect management internally. The

Hawk 2 (Wide bus) Family Install Guide, Rev. C2The physical design characteristics of the drive(s)described herein, serve to minimize EMI radiationwh

Hawk 2 (Wide bus) Family Install Guide, Rev. CPublication Number: 77767465, Rev. CPrinted in USASeagate Technology, Inc.920 Disc DriveScotts Valley,

Hawk 2 (Wide bus) Family Install Guide, Rev. CBefore you beginVerify that the system is switched off and discon-nected from main power before any in

Hawk 2 (Wide bus) Family Install Guide, Rev. C4• Inspect drive for possible shipping damage. All claimsof this type should be filed promptly with the

Hawk 2 (Wide bus) Family Install Guide, Rev. CTo insure optimum reliable equipment op-eration, it is required that technical supportpersonnel discharg

Hawk 2 (Wide bus) Family Install Guide, Rev. C6Safety instructions1. The disc drive(s) are to be installed in a customersupplied enclosure where the

Hawk 2 (Wide bus) Family Install Guide, Rev. C 7Sicherheitsanleitung1. Däs Gerät ist ein Einbaugerät, vorgesehen für einemaximale Umgebungstemperatur